Two In One Closed Loop Stepper Drive Drive Nema17 Nema23 Easy Servo Motor

Product Detail

TS508-B is closed loop stepper drive,same technology,the only difference is that one drive can drive two easy servo motor separately and at same time.The advantage is to save space,save time to install,and save cost.Check its detail information as following:

TS508-B(2 AXIS IN 1 HYBRID SERVO DRIVE)

Specifications

?Advanced 64bit DSP dual core technology

?Two hybrid servo motors can be synchronous or separately controlled via RS485

?Auto recognized the property of hybrid servo motor after power up.

?Work smoothly, high torque output at medium/high speed; fast response ,and low heating ,low vibration.

? 0—10VDC analog input for speed mode,and support IO speed control function.(customized)

?Adopt advanced variable current and variable frequency technology, it can reduce motor and drive heating and vibration.

?The max pulse frequency is 500KHZ,(the default is 200KHZ)

?The two motors can be controlled by one pulse command or two separately channels pulse command.

?The voltage of input pulse is 4.5vdc—28vdc, no need connect any resistor

?Support RS232 for ProTurner by PC(special cable ,please contact ECON technology for this cable)
?Work smoothly, high torque output at medium/high speed; fast response ,and low heating ,low vibration.

 

Application:

It can be used in various kinds of machines, such as fast gate,laser cutters,laser markers, high precision X-Y tables,labeling machines ,medical equipment,3D printer ,electronicdevice ,packing ,robot and so on. Its unique features make the TS508-B an ideal solution for applications that require both low noise and high speed performances.

Drive feature and selection guide
Drive model	TS508-B
Voltage	24~50VDC
Max current output	8A
Vector   over-load current	18A
weight	0.2kg
Matched   closed loop stepper motor	TC42(TC42-03, TC42-04,TC42-06,TC42-08) TC57 series[TC57-10,TC57-22C,TC57-28,TC57-30BK] TC60 series [TC60-20,TC60-30,TC60-40] Default (TC28,TC35 or   other manufacturer closed loop stepper motor)
Control technology	64bit floating-point dual-core  DSP vector closed loop control
Pulse Frequency	Max 500KHZ,the default is   200KHZ
Protection	Over- voltage, under-voltage   ,over-current, overload
Signal   input	Pulse,direction,enable   signal differential input, port electric level 4.5VDC—28VDC, no need to   connect any resistor
Signal   output	OC output, the max output   current is 100MA, need to connect a pull-up resistor, Max pull-up   voltage24VDC
Encoder   feedback	AB   encoder differential input, single-end can customized
Subdivision	Default   1600/rcv, DIP to set  200~51200
Open-close   selection	MT1 and MT2 can   set close loop or open loop, set by host computer
Using   environment	-5?~55?
Common Customized   Request	0~5V   or 0~10V analog voltage speed function, Same   or separate drive 2pc brush motor(A and B channel encoder, encoder signal   differential or single-end is ok) One   RS485 host line separately to control 2pcs stepper motor,2pcs hybrid servo   mtor,2pcs brush motor

Function Description

The drive set micro-step, motor initial direction and other function setting by 8 DIP switches, details as following:

 

Pulse/REV Table

Pul/REV	SW1	SW2	SW3	SW4
Default	ON	ON	ON	ON
800	OFF	ON	ON	ON
1600	ON	OFF	ON	ON
3200	OFF	OFF	ON	ON
6400	ON	ON	OFF	ON
12800	OFF	ON	OFF	ON
25600	ON	OFF	OFF	ON
51200	OFF	OFF	OFF	ON
1000	ON	ON	ON	OFF
2000	OFF	ON	ON	OFF
4000	ON	OFF	ON	OFF
5000	OFF	OFF	ON	OFF
8000	ON	ON	OFF	OFF
10000	OFF	ON	OFF	OFF
20000	ON	OFF	OFF	OFF
40000	OFF	OFF	OFF	OFF

 

 

Remark:Above micro-step is the standard of this drive,for others,based on customer’s request or host to set,the range is 200~51200

SW5:Motor 1 DIR,off=CCW,on=CW

SW6:Motor 2 DIR,off=CCW,on=CW

 

Motor Selection

Mode	SW7	SW8
Self-Test	ON	ON
LD	OFF	ON
PM	ON	OFF
FOC	OFF	OFF

Remark:

Self-test mode:if SW7 and SW8 are in ON,ON,the motor 1 and motor 2 will continuous move with 60RPM one round for CW,one round for CCW

 LD mode: full close loop control with high current, good stiffness,and high standstill locked torque;

PM: suitable for position to position mode with high speed start and stop

FOC:space vector control, which can be used for all command application